Have you ever wondered why your Peragon bed cover isn’t performing up to expectations?

This compact, robust cover, despite its merits, can sometimes pose challenges to truck owners.

Let’s explore the nitty-gritty of Peragon bed cover problems and explore practical solutions, all while keeping our discussion concise, informative, and engaging. Stay tuned to unravel the mystery!

Common Peragon Bed Cover Problems

Issues with the Installation of Paragon Bed Covers

Dealing with Water Leakage

One of the most common problems you may encounter with Peragon bed covers is water leakage.

It happens when water or moisture accumulates between the seal of the cover and the truck bed, which can lead to staining, rusting, and other wear on your truck.

To combat this, you need to make sure all components are properly sealed and installed.

Start by applying 3M weatherstrip adhesive to all seams and corners of your bed cover.

Then, apply a protective silicone sealant to the edges and bottom of the bed cover.

Finally, regularly inspect and maintain your bed cover by applying fresh layers of silicone sealant and weatherstrip adhesive to ensure a tight seal at all times.

Addressing Difficulty in Opening or Closing

You may also face difficulties when opening or closing your Peragon bed cover. This is usually due to a faulty latch system.

There are several steps you can take to address this. Begin by cleaning and lubricating the locking system with silicone spray, as well as tightening any loose screws.

You should also check to make sure that the latch handle is properly aligned and that all parts are in their expected positions. If your latch seems beyond repair, you may want to replace it.

Also, inspect for dents or bends in the truck bed rail where the latch is mounted, as these can throw off alignment.

You can use a putty knife to remove any dents and then straighten out any sharp bends so that everything lines up properly.

Solving the Rust Problem

Solving the Rust Problem

Rust can be a major problem for a Peragon cover if not addressed. There are a few solutions to prevent your Peragon bed cover from rusting.

Start by keeping your cover clean, as dust and dirt can lead to oxidation, which causes rust.

Hose it down with water and remove any dirt or grime that might be stuck on its surface.

You can also apply a protective coating such as wax or oil-based material to further protect your bed cover from rust.

Be sure that the fasteners and other hardware used with your Peragon bed cover are resistant to rust, so they won’t corrode over time.

Prefer stainless steel bolts and screws over any other kind of metal fastener if possible.

Preventing Scratching

Peragon Bed Covers are prone to get scratched, especially when dirt and debris come in contact while opening and closing the cover.

Regularly cleaning your Peragon Bed Cover with a microfiber cloth will help remove any dirt and debris that may be stuck in the bed cover tracks.

This can reduce the risk of scratching your truck bed. Applying a coat of wax to your Peragon Bed Cover can help minimize scratches.

Make sure to replace worn-out components such as tracks or rollers to avoid causing more scratches on your truck bed.

Reducing Bad Noise

Peragon Bed Covers can produce a lot of noise when in use, usually caused when the cover rubs against the bed or truck cab.

To reduce the noise, inspect the cover for any damage and make sure all fasteners are securely tightened.

Apply lubricant regularly to hinges and joints to help keep them in good working order and reduce noise when opening and closing the bed cover.

You can also add insulation between the bed cover and truck cab to help reduce vibrations and therefore noise.

Installing rubber gaskets between the bed rail clamps will also help reduce vibrations and noise caused by the movement of the bed cover on your truck cab’s surface.

Read About:  12 Common Lomax Tonneau Cover Problems And Quick Fixes

Tackling the Fading Problem

Fading is a common problem with most covers, including Peragon bed covers, as they’re exposed to the sun and rain constantly.

This can lead to the color of your Peragon bed cover fading over time, making it look less attractive.

There are several ways to prevent the fading of your Peragon bed cover. Regular cleaning and applying a UV-protective spray can help reduce the fading effect.

Keeping your bed cover out of direct sunlight as much as possible and cleaning it regularly can also help to maintain its original color.

If the fading is severe, consider getting a professional detailing service to help restore the color of your bed cover.

They can apply a high-quality UV-resistant paint or coating that can resist fading and bring back its shine.

The Durability of Peragon Bed Covers: Do They Stand the Test of Time?

The Durability of Peragon Bed Covers: Do They Stand the Test of Time

As a discerning customer, you deserve to know about the common problems associated with Peragon bed covers.

One of the primary concerns people have is about durability. Are Peragon bed covers long-lasting? Let’s delve deeper into this topic to shed some light on it.

Material Quality: The Foundation of Durability

When it comes to the durability of any product, the quality of materials used in its construction plays a pivotal role.

Peragon bed covers are crafted from aluminum. This metal is known for its strength and lightness, but how does it fare over time when exposed to various weather conditions?

Aluminum can corrode if not properly treated. This means if the protective coating on your Peragon bed cover wears off, the aluminum underneath could potentially start to corrode.

This corrosion might not be noticeable at first but could progress over time, leading to aesthetic and functional issues.

Weather Exposure: The Unseen Enemy

Another factor that can affect the durability of your Peragon bed cover is exposure to harsh weather conditions.

If you live in an area with high rainfall or snowfall, or where the sun’s UV rays are particularly strong, your bed cover could be under constant assault.

Over time, these conditions could cause the color to fade, the material to warp, or the moving parts to rust or seize.

Mechanical Wear and Tear: The Price of Function

Peragon bed covers are retractable, meaning they have moving parts. As with any mechanical system, these parts can wear out over time, especially if not properly maintained.

The retracting mechanism might start to jam or become less smooth in its operation.

If not addressed promptly, this could lead to more serious issues, potentially requiring costly repairs or replacement.

Handling and Installation: The Human Factor

Lastly, how you handle and install your Peragon bed cover can significantly impact its longevity.

If the bed cover is not correctly installed, it might not function as intended, and this could also lead to premature wear and tear. Misuse, such as overloading the bed cover, could also damage it.

Weather Resistance: Problems Related to Climate Conditions

The Impact of Rain on Peragon Bed Covers

As a user of a Peragon bed cover, you may have faced the problem of water leakage. This is common during heavy rainfalls or when washing your truck.

Despite Peragon’s promise of durability, the rubber seals that are supposed to keep water out can fail, allowing water to seep in.

Over time, this constant exposure to water can lead to rusting of the cover’s aluminum panels.

To prevent this, you must regularly check the rubber seals for signs of wear and tear. Also, ensure you replace any damaged seals immediately to maintain the cover’s water resistance.

Heat-Induced Issues: Warping and Fading

Intense heat can also pose a problem for your Peragon bed cover. Especially in hot climates or during the summer months, the cover can warp or even fade in color due to prolonged exposure to the sun’s ultraviolet (UV) rays.

Read About:  Can You Use A Tonneau Cover With A 5th Wheel Hitch?

Here’s how you can handle this issue: Use a UV-protectant spray. Regular application of this spray can help maintain the color and structural integrity of your bed cover.

It’s also essential to park your truck in shaded areas whenever possible to minimize direct sun exposure.

The Dilemma of Snow and Ice Accumulation

For those residing in colder climates, the accumulation of snow and ice is another issue you might encounter with your Peragon bed cover.

The weight of the snow can strain the retractable system, making it difficult to open and close the cover.

Additionally, the freezing temperatures can cause the rubber seals to become brittle and crack, reducing the cover’s effectiveness in keeping your truck bed dry.

Here’s a simple solution: Regularly clear the snow off your cover and apply a silicone-based lubricant to the rubber seals. This can help maintain their flexibility and prevent cracking.

Troubleshooting Locking Mechanism Failures in Peragon Bed Covers

Identifying the Issue with the Locking Mechanism

Firstly, you need to determine the exact problem with your Peragon bed cover’s locking mechanism.

Begin by conducting a thorough inspection of the entire system. Check the lock, the key, and the moving parts of the bed cover. As you do this, look for any visible signs of damage or wear.

Testing the Key

After inspecting the locking mechanism, turn your attention to the key. Does it fit smoothly into the lock?

If it doesn’t, it may be the source of your problem. You should try using a spare key if you have one. If the spare key works perfectly, it’s clear that your original key is worn out or damaged.

Inspecting the Locking Mechanism

The problem might reside in the locking mechanism itself. To assess this, carefully observe the lock as you insert and turn the key.

Is the lock responding as it should? If the key turns but the lock doesn’t respond, there may be an internal issue.

Checking for Dirt and Debris

Sometimes, the issue is as simple as a dirty or clogged lock. Over time, dirt, dust, and debris can build up inside the locking mechanism, hindering its operation.

To resolve this, use a can of compressed air to blow any potential obstructions out of the lock. Be careful not to damage any of the internal components while doing this.

Lubricating the Locking Mechanism

If your Peragon bed cover’s lock is sticky or stiff, it might just need some lubrication. Apply a silicone-based lubricant directly into the lock.

This should help the key to turn more smoothly, and it may solve the problem. Ensure to wipe away any excess lubricant to prevent dirt build-up.

Seeking Professional Help

If you’ve tried all the steps above and the problem persists, it’s probably time to seek professional help.

A locksmith or a Peragon bed cover specialist can diagnose and fix the problem. Don’t be discouraged; sometimes, these issues require an expert’s touch.

Comparing Peragon Bed Covers to Competitor Brands: Strengths and Weaknesses

Comparing Peragon Bed Covers to Competitor Brands: Strengths and Weaknesses

Aluminum Design

The first step in understanding the strengths and weaknesses of Peragon bed covers is to delve into their key features.

One of the standout aspects of Peragon bed covers is their retractable aluminum design.

Unlike many tonneau covers, a Peragon cover retracts like an accordion towards the cab side of the truck bed.

This design allows for full use of your truck bed, and the cover is easily removable when needed.

Stainless Steel Hardware

Peragon bed covers come with stainless steel hardware upgrades that include a dual locking bar, tailgate seal, LED light, and paint match.

The dual locking bar upgrade uses the same keyed lock to pin both the driver and passenger side of the cover, providing an extra layer of security.

Tailgate Seal

The tailgate seal helps keep water from seeping into the truck bed from the sides and bottom of the tailgate.

Read About:  Will A Ram 1500 Tonneau Cover Fit A Ram 2500?

The LED light provides interior light when using the tonneau cover in the closed position, and the paint match feature ensures the cover blends in seamlessly with your existing truck color.

Space-Saving Design

One of the unique selling points of the Peragon bed cover is its space-saving design. Some covers roll up into a canister, leaving you with a foot of wasted space at the cab end of your truck.

However, the Peragon bed cover, when in use, provides inside storage that spans the full length of the bed. When you no longer need the cover, you can retract it and pull it out.

The locking system is reliable and easy to use, and the entire system maintains a low profile that doesn’t disrupt the natural look of your truck.

Importantly, the Peragon tonneau cover is a product made in the USA, straight out of Wisconsin.

Installing

Installing a Peragon bed cover is a breeze, thanks to the company’s detailed video tutorials that guide you through every step of the installation process.

These videos are paired with a well-written installation manual filled with helpful visuals.

Comparing Peragon Bed Covers to Other Brands

To give you a balanced view, let’s look at some other popular brands on the market.

The BAKFLIP MX4, Gator EFX, UnderCover Elite, BAK Revolver X2, and RetraxOne MX are some of the top competitors.

BAKFLIP

The BAKFLIP MX4 boasts an aluminum panel construction and can hold up to 400 lbs. It comes with a 5-year warranty and features a no-drill installation process.

Gator

The Gator EFX is a folding type cover made from heavy-duty aluminum panels. It can support up to 300 lbs and offers a no-drill installation process.

This cover is unique due to its tri-folding design and polymer-coated panels that resist scratches, dents, and heat. However, when folded upright, it obstructs the cab’s rear view.

UnderCover

The Elite is a single-piece truck bed cover that can hold up to 500 lbs. Made of UV-treated ABS composite, it features an integrated lock and latch mechanism, and its support arms allow the cover to stay up when opened.

This cover carries a premium price, reflecting its premium build.

BAK

The BAK Revolver X2 offers a rollback type cover that combines the protection of a hardcover with the advantages of a roll-up design.

It supports up to 400 lbs, can be opened from either side of the bed with the tailgate down, and doesn’t block the rear window when rolled up.

However, getting the cover aligned properly during installation is critical for optimal performance.

FAQs

How Can I Address Water Leakage In My Peragon Bed Cover?

To address water leakage, make sure all components are properly sealed and installed.

You should apply 3M weatherstrip adhesive to all seams and corners of your bed cover, and apply a protective silicone sealant to the edges and bottom of the bed cover.

Regularly inspect and maintain your bed cover by applying fresh layers of silicone sealant and weatherstrip adhesive to ensure a tight seal.

How Can I Prevent Rust On My Peragon Bed Cover?

To prevent rust, keep the cover clean and remove any dirt or grime that might lead to oxidation.

You can also apply a protective coating such as wax or oil-based material, and use rust-resistant fasteners like stainless steel bolts and screws.

How Can I Prevent Scratches On My Peragon Bed Cover?

Regular cleaning of the bed cover with a microfiber cloth helps reduce the risk of scratching.

Also, applying a coat of wax can provide a protective layer against dirt and debris that could cause scratches.

Replacing worn-out components like tracks or rollers can also help prevent scratches.

Final Words

Navigating through Peragon bed cover problems need not be a daunting task.

With the right knowledge at your fingertips, you can turn these challenges into opportunities for understanding and growth.

Remember, every problem has a solution. So keep exploring, and keep your truck bed safe and secure with your Peragon cover!

Leave a Reply

Your email address will not be published. Required fields are marked *